Laboratories :

INFORMATION ON INFRASTRUCTURE AND OTHER
RESOURCE AVAILABLE ( Laboratories)
01	DIGITAL LABORATORY
02	ANALOG LABORATORY
03	MICROPROCESSOR
04	INFORMATION PROCESSING LAB
05	COMPUTER NETWORKS LABORATORY
06	ADVANCE COMPUTING LABORATORY
07	SOFTWARE DEVELOPMENT LABORATORY
08	MULTIMEDIA LABORATORY

1. DIGITAL LABORATORY ( Detail Configuration)

ScienTech Digital Lab-ST 2611 make experimental setup with power supply, breadboard, pulse genarator, DC power -supply, 7-segment LCD display, LED display, Logic probe, 8-bit Data switches, Pulser Switches with mode selection to carry out following experimentations:

Sr. no	Model	Details
01	ScienTech DB-13	4-Bit synchronous binary Counter implementation
02	ScienTech DB-07	Binary to Gray Code Conversion
03	ScienTech DB-04	Implementation of De-Morgan’s theorem
04	ScienTech DB-03	Ex-OR Gate Implementation
05	ScienTech DB-09	Encoder/Decoder Implementation
06	ScienTech DB-05	Ex-OR Gate applications
07	ScienTech DB-02	Realization of Universal gate NAND/NOR
08	ScienTech DB-11	Realization of Flip-Flops
09	ScienTech DB-12	Realization of Shift Registers
10	ScienTech DB-10	Multiplexer / Demultiplexer Implementation
11	ScienTech DB-06	Realization of Code conversion
12	ScienTech DB-14	4-BIT Binary Ripple Counter Implementation
13	ScienTech DB-08	Binary Adder / Subtractor Realization
14	ScienTech DB-01	Realization of Logic gates

Note: For carrying out experimentation on individual basis in the subject of Digital Electronics 10 sets of Power Supply’s & Frequency Generators each with required components are also available in the lab (Normally a batch of 20 students are performing the practical during lab session).

2. ANALOG LABORATORY ( Detail Configuration)

ScienTech Anolog Lab-ST 2612 make experimental setup with power supply, breadboard, pulse genarator,DC power -supply, Toggel Switches, Function generator, Modulator generator, Potentiometer, Continuity tester and AC Voltage, for performing

following experimentations:

Sr. no	Model	Details
01	ScienTech AB-03	Common Base PNP transistor Characteristics
02	ScienTech AB-07	Common Collector PNP Transistor Characteristics
03	ScienTech AB-02	Common base NPN transistor charateristics
04	ScienTech AB-30	Zener Voltage regulator
05	ScienTech AB-16	Common Collector Amplifier
06	ScienTech AB-51	High Pass Low Pass Active Filter
07	ScienTech AB-52	Band Pass Active Filter
08	ScienTech AB-06	Common Collector NPN transistor characteristics
09	ScienTech AB-04	Common Emitter NPN transistor characteristics
10	ScienTech AB-17	Common Base Amplifier
11	ScienTech AB-33	Transistor Shunt Voltage Regulator
12	ScienTech AB-08	FET Characteristics
13	ScienTech AB-32	Transistor Series Voltage Regulator
14	ScienTech AB-05	Transistor Characteristics PNP

Note: For carrying out experimentation on individual basis in the subject of Analog/Basic Electronics 10 sets of Power Supply’s, CROs & Function Generators each with required components are also available in the lab (Normally a batch of 20 students are performing the practical during lab session).

3. MICROPROCESSOR (Detail Configuration)

Anshuman make Microprocessor kits are available for carrying out laboratory sessions in the subject of Microprocessors at second year level as per details given below:

8085 Kits 10 Nos.

8086 Kits 02 Nos.

8051 Kits 02 Nos.

4. INFORMATION PROCESSING LAB (Detail Configuration)

10 Computer terminals with configuration of P-V processor 2.5 GHz, 128 MB RAM, 20GB Hard Disk, CD-ROM is available for the use of students for implementation of programs in the subject of Information Theory and Coding along with trainer kits as listed below:

SN	Model	Details
01	ScienTech-ST2102	TDM Pulse Amplitude Modulation/ Demodulation Trainer kit
02	ScienTech- ST2103	TDM Pulse Code Modulation Transmitter trainer kit
03	ScienTech- ST2105	Delta Adaptive, Delta Sigma Modulation trainer kit
04	ScienTech- ST2106	Data formatting and carrier modulation transmitter kit
05	ScienTech- ST2106a	Sampling and reconstruction trainer kit
06	ScienTech- ST2104	TDM pulse Code modulation receiver trainer kit
07	ScienTech- ST2107	Carrier Demodulation and Data Deformatting Receiver trainer
08	ScienTech- ST2503	Multiplexer and Demultiplexer Coder and Decoder trainer kit
09	ScienTech- ST2110	PAM, PWM, PPM Modulation and Demodulation trainer kit

COMPUTING FACILITY
04	ADVANCE COMPUTING LABORATORY
Sr.No		Features	Details
1		No. of Systems connected to LAN	20
2		System Configuration	P-IV 3.2MHz, 80GB Hard disk ,512 MB RAM,1.44 MB Floppy Diskette, CD-ROM RW , 17” Color monitor , optical mouse.
3		Major Software packages available	Microsoft .NET, Turbo C, MS-Office, Front Page etc…
4		Special purpose facilities available	24 port 100Mbps Switches, Two 5 KVA Stabilizers, One 5KVA UPS , and Two ACs.
5		Other services	1 Mbps Lease line
6		Furniture	20 Computer tables, 20 chairs.

05	SOFTWARE DEVELOPMENT LABORATORY
Sr.No	Features	Details
1	No. of Systems connected to LAN	20
2	System Configuration	P-IV 3.2MHz, 80GB Hard disk ,512 MB RAM,1.44 MB Floppy Diskette, CD-ROM RW , 17” Color monitor , optical mouse.
3	Major Software packages available	Microsoft .NET, Turbo C, MS-Office, Front Page etc…
4	Special purpose facilities available	24 port 100Mbps Switches, Two 5 KVA Stabilizers, One 5KVA UPS , and Two ACs.
5	Other services	1 Mbps Lease line
6	Furniture	20 Computer tables, 20 chairs.

06	ADVANCE COMPUTING LABORATORY
Sr.No	Features	Details
1	No. of Systems connected to LAN	20
2	System Configuration	P-IV 3.2MHz, 80GB Hard disk ,512 MB RAM,1.44 MB Floppy Diskette, CD-ROM RW , 17” Color monitor , optical mouse.
3	Major Software packages available	Microsoft .NET, Turbo C, MS-Office, Front Page etc…
4	Special purpose facilities available	24 port 100Mbps Switches, Two 5 KVA Stabilizers, One 5KVA UPS , and Two ACs.
5	Other services	1 Mbps Lease line
6	Furniture	20 Computer tables, 20 chairs.

07	MULTIMEDIA LABORATORY
Sr.No	Features	Details
1	No. of Systems connected to LAN	15
2	System Configuration	P-IV 3.2MHz, 80GB Hard disk ,512 MB RAM,1.44 MB Floppy Diskette, CD-ROM RW , 17” Color monitor , optical mouse.
3	Major Software packages available	Microsoft .NET, Turbo C, MS-Office, Rational Rose suite enterprise.
4	Special purpose facilities available	24 port 100Mbps Switches, 5KVA UPS, and Three ACs.
5	Other services	Internet Server, CISCO Router, 1 Mbps Lease line
6	Furniture	15 Computer tables, 15 chairs.

Detail Specifications of Equipments available in laboratories.

	Sr.No.		Technical Specifications		Qty. Available
	1.		TRAINER KIT FOR PERFORMING EXPERIMENTS IN BASIC ELECTRONICS AND DEVICES General Specifications: Regulated DC Power Supplies (using low loss R core transformer ): + 5V-1 A (Fixed),+12V-500 mA(Fixed), -12 V-500 mA (Fixed), +12V-500 mA (Variable), -12 V-500 mA (Variable) AC Supply : 9V-0V-9V/500mA. Breadboard : Breadboard for making various circuits and testing them. External  components/ IC can be fitted conveniently. All components and breadboard are mounted on Glass epoxy PCB. Interconnection through Detachable flat ribbon cables. All rotary switches with DAP material. Function generator : Operating modes: Sine, Square, Triangular Frequency range 1 Hz to 100 KHz Modulation /Audio generator : Operating modes: Sine, Square, Triangular Frequency range 1 Hz to 10 KHz Continuity tester : For testing the continuity. Provided with Beeper Sound. Interconnection for Modules : 2 mm patch cords. Power Requirements : 230V+/- 10%, 50 Hz Accessories Included : Mains cord, Operating and Experimental Manual (with more than 20 designed experiments.) patch cords. Optional : Ready to use Experiment Boards (covering device characteristics and study of  various circuits) with wired components and circuit schematic drawn on top. Compatible to use with Analog Lab ST2612, Circuit design & test software Tina Pro, Component set.		01 With necessary accessories and Manual
	2		TRAINER KIT FOR PERFORMING BASIC EXPERIMENTS IN DIGITAL ELECTRONICS Breadboard: 172.5 mm x 128.5 mm Connections : 1685 DC Power Supply: +5V-1A, 5V 500mA,                              3V-15V 500mA(variable)                              -3V-15V, 500 mA (variable) Pulse Generator: Frequency range: 1 Hz to 1 MHz in 6 steps.                               Variable in between steps. Amplitude:3V-15V(CMOS), 5 V (TTL) Duty cycle: 50 %. TTL/CMOS Output Pulser Switches : 2 Nos. (Push to On) Data switches : 8 Nos. (Toggle switches for both TTL&CMOS) LED display : 8 Nos. (TTL/CMOS Mode) Seven Segment Display : 3 Nos. Logic Probe : Logic level indicator for TTL/CMOS. Power : 230V, + 10%, 50 Hz. Weight : 3 kgs. (Approx). Dimensions (mm) : W385, H148, D323. Accessories included : Operating and Experimental Manuals, Patch cords, Overlay System. Optional- Component Set. Optional: Ready to use Experiment Boards (covering study of various Logic circuits) with wired  components and circuit schematic drawn on top.		01
03		Sampling and Reconstruction Trainer Crystal Frequency : 6.4 M. Hz Sampling Frequency : 2, 4, 8, 16 & 32 KHz (Switch Selectable) On-Board Generator : Synchronized 1KHz Sinewave (5Vpp) Duty cycle : 0-90% in decade steps (Switch Selectable) L. P. Filters : Butterworth 2^nd & 4^th order; Filter Cut-off frequency 3.4 KHz Test Points : 51 Interconnections : 4mm Sockets Power: 230V + 10%50Hz Dimensions (mm): W325, H90, D255 Weight : 2.4Kg (approx.) Accessories included: Manuals, Set of patch cord, Line cord		01
04		TDM pulse amplitude Modulation Demodulation TrainerCrystal Frequency : 6.4 M. Hz Analog Input Channels : 4 Multiplexing : Time Division Multiplexing Modulation : Pulse Amplitude Modulation On-board Analog Signal : 250 Hz, 500Hz, 1KHz, 2KHz (Sine Wave Synchronized to sampling pulse) Adjustable Amplitude and separate variable DC Level Sampling Rate : 16 KHz/ Channel Sampling Pulse : With Duty Cycle variable from 0-90% in decade steps Clock Regeneration at Receiver : Using PLL Low Pass Filter Cut-Off Frequency: 3.4 KHz Test Points : 52 Interconnections : 4mm Sockets Power: 230V + 10%50Hz Dimensions (mm): W325, H90, D255 Weight : 2.4Kg (approx.) Accessories included: Manuals, Set of patch cord, Line cord		01
05		TDM pulse code Modulation Transmitter TrainerCrystal Frequency : 6.4 M.Hz On-board Generators : (1) Adjustable Amplitude Sine Generator of 1&2 KHz  frequency (synchronized) (2) Variable Amplitude DC Level (2 Nos.) Input Channels : 2 Multiplexing : Time Division Multiplexing Modulation : Pulse Code Modulation Sync Signal : Pseudo Random Sync. Code Generator Error Check Code: Off-Odd-Even_Hamming Operating Modes : Fast 16KHz/channel (approx.) Slow 68mHz/channel (approx.) Test Points : 49 Interconnections : 4mm Sockets Power: 230V + 10%50Hz Dimensions (mm): W325, H90, D255 Weight : 2.4Kg (approx.) Accessories included: Manuals, Set of patch cord, Line cord		01
06		TDM pulse code Modulation Receiver Trainer Input Channels : 2 TDM Serial Input Demodulation : Pulse Code Demodulation Clock : Regeneration by PLL Low Pass Filter : Butterworth- 4^th order 3.4 KHz cutoff Frequency (2 no.s) Operating Speed : Fast-16 KHz/channel; Slow 68mHz/channel (approx.) Error Detection : Off-Odd-Even Parity Hamming Code Error Correction: Hamming code Test Points : 56 Interconnections : 4mm Sockets Power: 230V + 10%50Hz Dimensions (mm): W325, H90, D255 Weight : 2.4Kg (approx.) Accessories included: Manuals, Set of patch cord, Line cord		01
07		Delta , Adaptive Delta and Delta Sigma Modulation /Demodulation Trainer Crystal Frequency : 4.096 M. Hz Sampling Frequency : 32, 64, 128, 256KHz (Switch Selectable) On-Board Generator : Synchronized & Adjustable Amplitude Sinewave generator at 250Hz, 500Hz, 1KHz, 2KHz. Separate variable D.C. level Integrators: 4 integrator gain settings Norm, x2, x4, x8 L. P. Filters : 4^th order Butterworth (3.4 KHz Cut Off Frequency) Test Points : 59 Interconnections : 4mm Sockets Power: 230V + 10%50Hz Dimensions (mm): W325, H90, D255 Weight : 2.4Kg (approx.) Accessories included: Manuals, Set of patch cord, Line cord		01
08		Data Formatting and Carrrier Modulation Transmitter Trainer Input : Two channel Time Division Multiplexed Data Data Formats : NRZ(L), NRZ(M) RZ, Biphase (Manchester), Biphase (Mark), Diffeentially encoded dibit pair Carrier Modulation : FSK, PSK, ASK & QPSK On-board carrier: Sinewave Synchronised to transmit data at 1.44 MHz, 960KHz, (0 deg. Phase) 960 KHz (90 deg. Phase) Test Points : 38 Interconnections : 4mm Sockets Power: 230V + 10%50Hz Dimensions (mm): W325, H90, D255 Weight : 2.4Kg (approx.) Accessories included: Manuals, Set of patch cord, Line cord		01

09	Carrier Demodulation and Data Reformatting Receiver Trainer Input : from Model ST2106 Ouput: 2 Channel TDM Multiplexed Data Stream Deconditioning options : NRZ(M) RZ, Biphase (Manchester), Biphase (Mark), Diffeentially encoded dibit pair to NRZ(L) Carrier Demodulation: : 1. ASK – Rectifier diode 2. FSK – PLL Detector 3. PSK – Square Loop Detector 4. QPSK – Fourth Power Loop Detector On-board carrier: Sinewave Synchronized to transmit data at 1.44 MHz, 960KHz, (0 deg. Phase) 960 KHz (90 deg. Phase) Carrier Demodulation : Biphase Clock recovery : by PLL Test Points : 54 Interconnections : 4mm Sockets Power: 230V + 10%50Hz Dimensions (mm): W325, H90, D255 Weight : 2.4Kg (approx.) Accessories included: Manuals, Set of patch cord, Line cord	01
10	PAM-PPM-PWM Modulation and Demodulation Trainer Pulse Modulation Techniques: (1) Pulse Amplitude Modulation (2) Pulse Width Modulation (3) Pulse Position Modulation On-board Sampling Frequencies (Pulse): 8KHz, 16KHz, 32KHz, 64KHz On-board Generators : (1) Sinewave 1KHz & 2 KHz(Gain adjustable) (2) Squarewave 1KHz & 2 KHz Low Pass Filter : 4th order BW Filter Voice Communication : Voice Link using dynamic mic & speaker AC Amplifier : With Adjustable Gain Control DC Output : 0-4V (Variable) Switched Faults : 8 No.s Test Points : 29 Interconnections : 4mm Sockets Power: 230V + 10%50Hz Dimensions (mm): W325, H90, D255 Weight : 2.4Kg (approx.) Accessories included: Manuals, Set of patch cord, Line cord	01
	Multiplexer /Demultiplexer Coder /Decoder Trainer Crystal Frequency : 4.096 MHz Analog Input Channels : 4 Digital Input Channels :16 On Board Analog Signals :250MHz , 500MHz,1KHz,2KHz(Adjustable Amplitude) On Board Digital Outputs : 1)16 square wave Frequencies (1KHz to 2MHz) 2)Clock Generator 3)8 bit data Modulation : Pulse Code Modulation Multiplexing : Time Division Multiplexing (4 Channel Analog and 16 Channel Digital) Coding : Manchester Coding and Decoding Test Points :27 Interconnections :4mm Sockets Dimensions (mm) : W325,H90,D255 Power : 230V +/-10%,50Hz Weight : 3Kg (approx) Accessories Included :Manual, Mains cord, patch cards	01

Computer Laboratories.

1. COMPUTER NETWORKS LABORATORY

SNo

Specification

Qty

1.

PIV DESKTOP COMPUTERS

Intel PIV 3.2 GHz , 800 MHz FSB Intel HT support,

865 GBF mother Board with HT 800 FSB support,

512 MB DDR SDRAM , 17’’ LG Flatron Colour Monitor

1.44 MB FDD , 80GB HDD(Seagate Barracuda 7200 rpm),52x CD-RW drive,Internet Ready keyboard ,optical mouse , ATX PIV cabinet, 10/100 Ethernet Card,

20

2.

Online UPS 5KVA

Input Voltage : 176 to 276 V AC, Frequency : 47-53 Hz, Power Factor : >0.95

Output Voltage :230 V AC,50 Hz sinewave, Power Factor : 0.7 Efficiency : >85%

Backup Battery : up to 4 hrs. Voltage : 240 V

General Transfer Time : 3msec Indications : Line,inverter,bypass, fault,load level

Alarm : Battery mode , battery low, overload,UPS fault Operating Temp :0-40%,95% RH Noise Level : <45db RS-232 : win 98/2000/NT,Novll, Unix/Linux

01

3.

Network Components

24 –ports 10/100 Mbps High performance

Express Ether Network Switch

b) GigaExpress 8-port Layer 2 Unmanaged Gigabit Switch

c) 24 – ports 10/100 Mbps High Performance Ethernet Hub

01

01

02

4.

5KVA Servo Controlled Voltage Stabilizer

CHARACTERISTICS	SINGLE PHASE
Input Voltage	170-270 VAC ,230± 1.0% Regulation (Adjustable Between 210-240 V)
Frequency	47 - 53 Hz
Wave from Distortion	None
Speed of Correction	20 V / Sec.
Regulation	± 1.0% from No Load to full load.
Ambient Temperature	0° to 55° C

02

2. ADVANCE COMPUTING LABORATORY

SNo.

Specification

Qty

1.

PIV DESKTOP COMPUTERS

Intel PIV 3.2 GHz , 800 MHz FSB Intel HT support,

865 GBF mother Board with HT 800 FSB support,

512 MB DDR SDRAM , 17’’ LG Flatron Colour Monitor

1.44 MB FDD , 80GB HDD(Seagate Barracuda 7200 rpm),52x CD-RW drive,Internet Ready keyboard ,optical mouse , ATX PIV cabinet, 10/100 Ethernet Card,

20

2.

Online UPS 5KVA

Input Voltage : 176 to 276 V AC Frequency : 47-53 Hz Power Factor : >0.95

Output Voltage :230 V AC,50 Hz sinewave, Power Factor : 0.7

Efficiency : >85% (AC TO AC) Backup Battery : up to 4 hrs. Voltage : 240 V

General Transfer Time : 3msec Indications : Line,inverter,bypass, fault,load level

Alarm : Battery mode , battery low, overload,UPS fault

Operating Temp :0-40%,95% RH Noise Level : <45db

RS-232 : win 98/2000/NT,Novll, Unix/Linux

01

3.

Network Components

24 –ports 10/100 Mbps High performance

Express Ether Network Switch

b) GigaExpress 8-port Layer 2 Unmanaged Gigabit Switch

c) 24 – ports 10/100 Mbps High Performance Ethernet Hub

01

01

02

4.

5KVA Servo Controlled Voltage Stabilizer

CHARACTERISTICS	SINGLE PHASE
Input Voltage	170-270 VAC ,230± 1.0% Regulation (Adjustable Between 210-240 V)
Frequency	47 - 53 Hz
Wave from Distortion	None
Speed of Correction	20 V / Sec.
Regulation	± 1.0% from No Load to full load.
Ambient Temperature	0° to 55° C

02

3. SOFTWARE DEVELOPMENT LABORATORY

Sr.

No.

Specification

Qty

1.

PIV DESKTOP COMPUTERS

Intel PIV 3.2 GHz , 800 MHz FSB Intel HT support,

865 GBF mother Board with HT 800 FSB support,

512 MB DDR SDRAM , 17’’ LG Flatron Colour Monitor

1.44 MB FDD , 80GB HDD(Seagate Barracuda 7200 rpm),52x CD-RW drive,Internet Ready keyboard ,optical mouse , ATX PIV cabinet, 10/100 Ethernet Card,

20

2.

Online UPS 5KVA

Input Voltage : 176 to 276 V AC Frequency : 47-53 Hz Power Factor : >0.95

Output Voltage :230 V AC,50 Hz sinewave, Power Factor : 0.7

Efficiency : >85% (AC TO AC) Backup Battery : up to 4 hrs Voltage : 240 V

General Transfer Time : 3msec Indications : Line,inverter,bypass, fault,load level

Alarm : Battery mode , battery low, overload,UPS fault

Operating Temp :0-40%,95% RH Noise Level : <45db

RS-232 : win 98/2000/NT,Novll, Unix/Linux

01

3.

Network Components

24 –ports 10/100 Mbps High performance

Express Ether Network Switch

b) GigaExpress 8-port Layer 2 Unmanaged Gigabit Switch

c) 24 – ports 10/100 Mbps High Performance Ethernet Hub

01

01

02

4.

5KVA Servo Controlled Voltage Stabilizer

CHARACTERISTICS	SINGLE PHASE
Input Voltage	170-270 VAC ,230± 1.0% Regulation (Adjustable Between 210-240 V)
Frequency	47 - 53 Hz
Wave from Distortion	None
Speed of Correction	20 V / Sec.
Regulation	± 1.0% from No Load to full load.
Ambient Temperature	0° to 55° C

02

4. MULTIMEDIA LABORATORY

Sr.N.	Specification	Qty
1.	PIV DESKTOP COMPUTERS Intel PIV 3.2 GHz , 800 MHz FSB Intel HT support, 865 GBF mother Board with HT 800 FSB support, 512 MB DDR SDRAM , 17’’ LG Flatron Colour Monitor 1.44 MB FDD , 80GB HDD(Seagate Barracuda 7200 rpm),52x CD-RW drive,Internet Ready keyboard ,optical mouse , ATX PIV cabinet, 10/100 Ethernet Card,	15
4.	Online UPS 5KVA Input Voltage : 176 to 276 V AC Frequency : 47-53 Hz. Power Factor : >0.95 Output Voltage :230 V AC,50 Hz sinewave, Power Factor : 0.7 Efficiency : >85% (AC TO AC) Backup Battery : up to 4 hrs. Voltage : 240 V General Transfer Time : 3msec Indications : Line,inverter,bypass, fault,load level Alarm : Battery mode , battery low, overload,UPS fault Operating Temp :0-40%,95% R Noise Level : <45db RS-232 : win 98/2000/NT,Novll, Unix/Linux	01
6.	Network Components 24 –ports 10/100 Mbps High performance Express Ether Network Switch b) GigaExpress 8-port Layer 2 Unmanaged Gigabit Switch c) 24 – ports 10/100 Mbps High Performance Ethernet Hub l) Fibre to UTP Transreceiver 10Mbps	01 01 02 04
8.	Laser Printer Network Compatible Model No. HP 2200	01
9.	LCD Data Projector With facility of PC card Slot enable wireless connection and PC less presentation. Technical specifications Display : 3x0.9” poly silicon TFT Resolution : XGA 1024x768	01

Licensed Software available with IT Department :

v Microsoft Windows 2003 Server

v Microsoft Windows XP

v Microsoft Visual Studio

v IBM Rational Enterprise Suit

v Microsoft Office XP

v Turbo LINUX

v Red Hat Enterprise Linux 4

v Norton Antivirus 2003